10/22 double magazine body
- Thread starter Gonzobird
- Start date
timboy
.44 mag
I'm thinking no as it is one magazine body capable of holding more than 10 rounds.
fnfalguy
.308 Win
I would think it is ok as it is two separate magazines. You have to eject the magazine and reinsert the full side.
No different than a coupler.
This is a far better thing than that crazy triple coupler.
Acer-m14
20×102mm Vulcan
save your $$$ .. find some 1/4 " plastic and cut to fit in the recess of the mag bottom and epoxy it in and pop another mag on the other side ..
piece of cake .. .. not hard to double stack 10/22 rotor mags ...
pew pew pew .. eject ... flip .. pew pew pew ..
i did the same with all my Mini14 10 rnd mags .. little thinking and some epoxy .. there back to back .. shoot , flip , shoot ..
piece of cake .. .. not hard to double stack 10/22 rotor mags ...
pew pew pew .. eject ... flip .. pew pew pew ..
i did the same with all my Mini14 10 rnd mags .. little thinking and some epoxy .. there back to back .. shoot , flip , shoot ..
Acer-m14
20×102mm Vulcan
Can you take the bottom of the mag off with that set-up?
knuts
.45 acp
Should be gtg, i have the triple coupler.
If I wanted a back to back 10/22 mag setup I would much rather have this nice slick integral body as opposed to two mags glommed together with glue. You would have to come up with a spacer plate as well as the 10/22 mags are slightly convex on the bottom.
It's only $10 people.
It's only $10 people.
Acer-m14
20×102mm Vulcan
Got mine today.
GTN
.308 Win
Range report
Probably by the 26th
So they sell a tool kit to put them together but I don’t buy one. All you need is a 9/64 Allen a pair of needle nose pliers and a 7/16 box end/open end wrench. The spring has to be turned 1 1/2 times and the box end wrench is perfect to turn the nut and captured spring.
The double Kross is lighter than one stock 10/22 mag body and it is smaller than two end to end. I will try them out Christmas at the range.
Cool.
Just got back from the range and trying out the double mag bodies. Conducted rapid fire tests with full magazines and slow fire with full magazines.
Had a couple of Failure to fire malfunctions but they were not caused by the magazines.
The magazine bodies lock up in the gun tightly and the bottom mag protrudes enough to get a hand on it to pull it out. They drop out freely without any hang ups. They locked up in the magwell securely.
The only real problem I had was trying to release the mag without actually dropping it on the table it took a couple of try’s to push the button releasing the mag while grasping it and getting it to come clear of the magwell.
If you are not worried about dropping the mag on the ground it is not an issue.
Overall I would give them a thumbs up and I would recommend them if you want a double mag without a coupler.
I run a tri mag coupler for competition and will not be replacing them with these.
Had a couple of Failure to fire malfunctions but they were not caused by the magazines.
The magazine bodies lock up in the gun tightly and the bottom mag protrudes enough to get a hand on it to pull it out. They drop out freely without any hang ups. They locked up in the magwell securely.
The only real problem I had was trying to release the mag without actually dropping it on the table it took a couple of try’s to push the button releasing the mag while grasping it and getting it to come clear of the magwell.
If you are not worried about dropping the mag on the ground it is not an issue.
Overall I would give them a thumbs up and I would recommend them if you want a double mag without a coupler.
I run a tri mag coupler for competition and will not be replacing them with these.