******OFF TO EBAY*****no longer available here.
Had this for a while and it seldom gets used, due to me jumping into the PCP Airgun world. Anyway, its a Hy Score Model 801, in .22 caliber. Shoots any .22 cal pellets very well. Made in Germany, and it even has captured screws, like on a...
Anyone have a lead-rated ladle they're not using? Must be between 4 and 6 ounce capacity. Thinking about trying my hand at some basic casting. Might be interested in whole casting setup ,if the price is right. I'm in mid-Westchester . PM or email:
ds1911 (at) iCloud.com
My EDC. A 1990's early Spyderco Endura that I cut a " wave" into. Been through thick and thin with this knife and have it on as I type this. Very generous deal, Minderasr..
Another vote fer der K55K. Walked into a tiny thrift shop with my lunch money, probably 12 years old back in the mid 1970's and the guy actually sold it to me. Flicked and flicked till it slipped out of my hand and stuck in my inner thigh. Still have the scar. Never told Mom, though. Wish I...
Didn't want to open the bag, so took some pics off the web to illustrate the M9 you'll be receiving. M9 bayonet/survival knife for the AR/M16/Mossberg 590 platforms. These were made by 4 subcontractors , this one being Tri- Technologies right here in NY. Properly marked with the 06MA8...
These might be the best deal going, as far as a quality Airguns and price point. They have a Lothar Walther match barrel, and these things really stack pellets. They come with sling, nice micrometer sights and stock spacers for young shooters. Grooved receiver top should you want to mount a...
If you reload 30-30, and just want to plink...you can use any 110 gr. 30 cal M1 Carbine bullets on the cheap and get great results. Have a 1950's vintage plain-Jane Win 94 Carbine with a period Lyman peep sight.. Had some military pull-downs and some old 2400 powder to burn up and did this on...
Used this to great success, and now all my arrows are cut. Tubing cutters distort the end , while this leaves a clean, perfect end. Moving it along. Works perfectly, and will cut aluminum, plastic, steel, etc. mounted on a new piece of 3/4" Melamine. Price $20 cash FTF, (won't ship this)...
Anyone in the lower Hudson Valley have a pound or two (or 4) of factory sealed 4895 powder? I have pistol powder, large and small rifle primers to trade or will buy outright. Pleasantville/Mt Pleasant area, but will drive to make the deal happen.
PM or email:
ds1911 (at) iCloud.com
What a beauty..Most Sheridan valves require a special tool to service. Tool is available, but just annoying to reseal, especially if your Sheridan hasn't been too well taken care of, and the valve is dirty/worn and seized in there. Did a few over the years and would recommend soaking in some...
I use these 40 grainers in my 218 bees and Hornets. The 218 bees COAL is too long for the Winchester 43’s magazines , so went with a shorter head. But loaded single shot, they are very accurate.
*********SOLD******
Upgraded, shop-air powered Snap On Coolant system tester. Used a few times and put back in the box. I beleive it has a couple of additional adapters included in the box.
$75 cash FTF in Pleasantville, or add $15 shipping to you, in the lower 48 states. Might trade for...
*****SOLD*******
Thinning collection...Older quality (pre-1968, no serial number) Marlin Model 99 in 22 Lr. Carbine shows very minor, normal wear, with no alterations, repairs, or abuse. Faithful copy of the USGI M1 Carbine, but chambered in .22 Lr. High condition little carbine that is...
Swap you even for 177 rds of Barnal Silver Bear .223 62 gr HP's on USGI stripper clips & a spoon/speed loader. Meet you halfway in Yonkers. Pm me if any interest..
Added one pistol a few years back and it took about 6 weeks to clear. This is after having my permit for well over 20 years , without incident. Also this came right after submitting to a second "safe inspection" for no apparent reason. Vermont's looking better and better
I beleive those are for the Dillon 550 press, as there are 4 stations and it takes the standard 7/8" dies. 650 & 750 presses have 5 stations. Square Deal B's cannot accept standard 7/8" dies.
As for Miltec’s M1D sniper, I might be wrong, but I’m skeptical of them using real USG I scope, barrel block, and mount. Have heard the repro scopes are OK. But mounts and barrel block are known to be Chinese, and not properly hardened. Threads strip out, and weapon will not hold zero. Just...